Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of BERGAMID® A800H - PA66 - Avient Corporation

Material Data Center offers the following functions for BERGAMID® A800H:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Bergamid A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
機械的特性 - 熱的特性 - 電気的特性. - その他の特性. - 材料特有の特性 - 試験片の成形条件.
Any use of this information falls under the rules of our disclaimer.
商品の説明文
BERGAMID A800H, PA66 unreinforced
general-purpose injection molding grades
high viscosity, heat stabilized,
flame class UL94: V-2
UL-listing
機械的特性乾燥/調湿単位テスト基準
ISO データ
引張弾性率 1600 / 3200 MPa ISO 527
降伏応力 60 / 80 MPa ISO 527
降伏ひずみ 25 / 4.5 % ISO 527
破壊呼びひずみ >50 / 22 % ISO 527
シャルピー衝撃強さ, +23°C N / N kJ/m² ISO 179/1eU
シャルピー衝撃強さ, -30ﾟC N / N kJ/m² ISO 179/1eU
ノッチ付きシャルピー衝撃強さ, +23°C 25 / 6 kJ/m² ISO 179/1eA
ノッチ付きシャルピー衝撃強さ, -30ﾟC - / 4 kJ/m² ISO 179/1eA
熱的特性乾燥/調湿単位テスト基準
ISO データ
溶融温度, 10ﾟC/min 261 / * °C ISO 11357-1/-3
荷重たわみ温度, 1.80 MPa 80 / * °C ISO 75-1/-2
荷重たわみ温度, 0.45 MPa 220 / * °C ISO 75-1/-2
線膨張係数, 平行 85 / * E-6/K ISO 11359-1/-2
線膨張係数, 直角 82 / * E-6/K ISO 11359-1/-2
1.5mm厚さでの燃焼性 V-2 / * class IEC 60695-11-10
試験片の厚さ 1.6 / * mm -
Yellow Card 可用 はい / * - -
厚さhでの燃焼性 V-2 / * class IEC 60695-11-10
試験片の厚さ 0.7 / * mm -
Yellow Card 可用 はい / * - -
電気的特性.乾燥/調湿単位テスト基準
ISO データ
比誘電率, 1MHz 5 / 3.6 - IEC 62631-2-1
誘電正接, 1MHz 2000 / 260 E-4 IEC 62631-2-1
体積抵抗率 1E10 / 1E13 Ohm*m IEC 62631-3-1
表面抵抗率 * / 1E10 Ohm IEC 62631-3-2
耐電圧 80 / 120 kV/mm IEC 60243-1
耐トラッキング性 600 / - - IEC 60112
その他の特性.乾燥/調湿単位テスト基準
吸水率. 8.5 / * % Sim. to ISO 62
吸湿率 2.8 / * % Sim. to ISO 62
密度. - / 1130 kg/m³ ISO 1183
材料特有の特性乾燥/調湿単位テスト基準
ISO データ
粘度数. 150 / * cm³/g ISO 307, 1157, 1628
試験片の成形条件.値単位テスト基準
ISO データ
射出成形, 樹脂温度 280 °C ISO 294
射出成形, 金型温度 40 °C ISO 294
特殊な特性
成形加工法.
射出成形., 異形押出成形.
納入形状.
ペレット.
特殊な特性.
熱安定化.
領域別の利用可能性
ヨーロッパ.
その他の情報
射出成形
PREPROCESSING
Max. Water Content 0,1%
Pre-Drying: 80°C 4 Hours
PROCESSING
Melt Temperature 280-300°C
Mould Temperature 40-80°C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.